How Do You Clear The AF Code On A Dryer?

The code AF normally indicates that the control senses a restricted air flow on most models of Kenmore Elite dryers. . … Check the flexible vent connection behind your dryer. Make sure that it is not kinked or clogged.

How do you clear the AF code on a dryer?

  1. Clean the lint screen.
  2. Check to see if the house vent from the dryer to the wall is crushed or kinked.
  3. Confirm that the house vent from the dryer to the wall is free of lint and debris.
  4. Confirm that the exterior vent exhaust hood is free of lint and debris.

How do you reset a Kenmore Elite dryer? To reset, unplug the power cord for 5 minutes. For example, suppose you press the n key twice to power off in another section for the same situation, then press the power key. My He3 doesn’t have an on or off button.

What does F mean on my dryer?

The F-01 error code indicates a primary control failure. The primary controls are located inside the main control panel where the dryer cycles and settings are displayed. Any burns or arcing on the motherboard where the wires are connected could mean the primary control was shorted out.

How do I turn off the control lock on my Kenmore Elite dryer?

The control lock is turned on or off by pushing and holding the drain/spin button for 3-5 seconds.

How do I reset my Huebsch dryer?

  1. Start with all the DIP switches in the two blocks under the display in the OFF position (down)
  2. Press reset button to clear memory.
  3. Press button to the left of the display to show start time for the dryer.

Why does my Cabrio dryer say af?

The AF code (Air Flow) on a Cabrio Dryer is signaling that the machine does not have proper airflow. … The excessive lint inside the drum shows that the lint is not being drawn into your dryer filter because of the poor circulation of air.

Why is my dryer running but not heating?

Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element. If you gather your tools and follow this guide, you may be able to solve basic dryer heating problems on your own.

Where is the reset button on a Kenmore?

There is no reset button for the compressor, but a model number is helpful in giving you a more specific answer. A click or hum as the compressor tries to start/run is one thing you might listen for. The problem with the start relay is not the compressor.

What does it mean when your dryer says F01?

7 Answers. The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.

What does F01 mean on my Whirlpool dryer?

The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.

How do I clear the error code on my Kenmore dryer?

Unplug the dryer for 5 minutes and then plug it in. If the code returns, then replace the main electronic control board. A button is stuck on the keypad on one of the two user interface control assemblies in the console. If you can’t free the button, replace the user interface control assembly with the stuck button.

How do you unlock a Kenmore Elite?

To unlock the dishwasher control panel, press and hold the NO HEAT DRY button for 4 deliberate seconds and the LOCK ON light should turn off. The control should then work normally.

How do I turn off the Control Lock on my Kenmore washer?

  1. The control panel being locked on the washer can be very concerning. …
  2. The model number is 45981 400. …
  3. Thank you for submitting your question. …
  4. Press and hold the “CHIME” button for 3 or more seconds to activate/deactivate the CL function.

How do I get the Control Lock off my washing machine?

Select and hold END OF CYCLE SIGNAL for 3 seconds until the CONTROL LOCKED Status light turns off. If that does not do it, try putting the machine into diagnostic mode. The washer must be empty and the control must be in the OFF state before pressing the touch-pad sequence to start the test. Close the door.

You May Like Also

  • ⚀ Was the first inscription in Sanskrit?
  • ◐ What chocolate can I use instead of candy melts?
  • ⚀ Where was digital photography invented?
  • ⯑ What is the SEC’s oversight role for the financial reporting and independent audit functions?
  • ⣿ Can bamboo grow 3 feet in 24 hours?
  • ⬗ How many arborists are in the US?
  • ☉ What are the causes of severe weather?
  • ⣿ Is raw-milk cheese healthier?
  • ⡾ What is the difference between Form 941 and 944?
  • ⡾ What is humanistic theory of personality?
  • Is sawn and honed sandstone slippery?
  • How much does a bluestone patio cost?
  • Is pepperoncini the same as banana peppers?
  • Why are benthic organisms important?
  • Is quartz cheaper than Silestone?
  • Is the argyranthemum plant a perennial?
  • Where is corn grown in India?
  • Do annual plants die every year?
  • How long does it take to get to Singapore?
  • How can I access a table from one database to another database?
  • Is Bart Simpson overweight?
  • What does slackening mean definition?
  • Does grass need light to grow?
  • What eats butterfly bushes?
  • How did Moses free the Israelites?
  • How can an antepartum hemorrhage be prevented?
  • How do you store a car battery in storage?
  • What is a herniated nucleus pulposus in lay terms?
  • How long do chlorinator cells last?
  • How do you install a sunbrella golf cart enclosure?
  • How are different types of soil formed?
  • How do you root a chenille plant?
  • What is an indirect retainer?
  • Where is your Suprailiac?
  • How long can you keep home canned tomatoes?
  • Who created Bonanza farms?
  • Does Priscilla get better Witcher 3?
  • Can a sole proprietorship business exist forever?
  • In which form does an information get transmitted through a neuron?
  • What happens if you break the Consumer Protection Act?
  • What is an allowance at closing?
  • Can white mold grow on concrete?
  • What is the polymer and monomer of nucleic acids?
  • Is political risk systematic or unsystematic?
  • Do I need a pencil for the GMAT?